Majoni Block 100 Flex Pontoon Dock Impact Corner Boat Fender - Single

The Majoni Block 100 Flex Pontoon Dock Impact Fender is a flexible 100 x 12 x 7 cm dock bumper that can be installed along a straight berth edge or formed around a suitable corner. It is available in white or navy and weighs approximately 1.8 kg.

Its UV-resistant rotation-moulded PVC body provides continuous low-profile protection while accommodating a change in dock direction. Pre-moulded mounting positions allow the fender to be secured to sound pontoon, jetty or marina structures using separately selected hardware.

Product Identification

• Brand: Majoni
• Product name: Majoni Block 100 Flex Pontoon Dock Impact Fender
• Marine Scene SKUs: SG-BLOCK-100-FLEX and SG-SG-BLOCK-100-FLEX-N
• Product category: Flexible pontoon and dock fender
• Dimensions: 100 x 12 x 7 cm
• Approximate weight: 1.8 kg
• Colours: White or Navy
• Quantity supplied: One selected fender

What Is the Majoni Block 100 Flex Used For?

It cushions a straight dock edge or a corner where a standard rigid-profile block fender cannot follow the structure. The flexible body helps maintain coverage through the change in direction.

What Is Included?

• One Majoni Block 100 Flex fender in the selected colour
• Integral mounting positions

What Is Not Included?

• Mounting screws, bolts, washers or backing plates
• Dock reinforcement
• Inflation pump or adaptor if pressure adjustment is required
• Additional berth fenders

How Do I Confirm the Corner Radius?

Offer the fender to the intended location without forcing it. The body should follow the corner smoothly while every mounting point remains flat against sound support. Do not bend it around a radius that causes whitening, creasing, cracking or excessive tension at the fixings.

What Is the Difference Between Block 100 Flex and Block 100?

Both are 100 x 12 x 7 cm berth fenders. The Flex version is intended to conform around suitable corners, whereas the standard Block 100 is best suited to a straighter protected section.

Construction and Design

• Flexible 100 cm dock-protection strip
• 12 cm height and 7 cm depth
• UV-resistant rotation-moulded PVC
• White and navy variants
• Pre-moulded fixing positions
• Can be installed flat or around a suitable corner

Installation and Safety

Fix the fender to sound structural material using corrosion-resistant hardware and adequate backing. Follow the curve gradually and use every required mounting position. Do not overstress the body or rely on weak fascia boards. Test the contact area at low speed after installation.

Maintenance

• Inspect bends and mounting points for cracks or deformation.
• Check every fastener and the underlying dock structure.
• Clean off sand and grit that could mark the hull.
• Inspect the full contact length after heavy weather or impact.
• Replace the fender if flexibility or structural integrity is reduced.

Key Features

• Flexible 100 x 12 x 7 cm profile
• Bends around suitable pontoon and dock corners
• UV-resistant rotation-moulded PVC
• Approximately 1.8 kg
• White or navy colour options
• Pre-moulded mounting positions
• Suitable for straight and curved berth sections

Frequently Asked Questions

Can the Block 100 Flex be mounted on a straight edge?
Yes. It can be used on straight sections as well as suitable corners.

Will it bend around any corner?
No. The radius must be gentle enough for the body and mounting points to sit without excessive stress.

Are fixings included?
No. Select corrosion-resistant hardware and backing for the dock construction.

Is it the same as the standard Block 100?
The dimensions are similar, but the Flex version is intended to conform around a corner.

How many units are required?
Use enough units to cover the complete expected hull contact path.

Specifications

Do not force the fender around an unsuitable radius; the body and all mounting positions must remain evenly supported.

• Choosing a selection results in a full page refresh.
• Opens in a new window.